View Issue Details

IDProjectCategoryView StatusLast Update
0001341Microcontrollers, shields, automation, arduino[All Projects] Generalpublic2022-02-02 22:45
ReporterDigitalMy 
PrioritynormalSeverityminorReproducibilityhave not tried
Status assignedResolutionopen 
Summary0001341: Make simple local UPS for 12V DC device
DescriptionBurned PicoUPS-120 so that it gives 6V only with battery power...

Found similar module XH-M238 Mini UPS
YX-X804
YX-X850
TagsNo tags attached.

Activities

DigitalMy

2021-02-26 03:40

administrator  

picoUPS-120-ATV-UPS.jpg (49,889 bytes)
picoUPS-120-ATV-UPS.jpg (49,889 bytes)

DigitalMy

2022-01-21 12:44

administrator   ~0007136

Last edited: 2022-01-27 22:33

View 3 revisions

Decided to build another 12V battery UPS
Use (solar) charge controller (10A) for input and cut-off battery power.
Charger is set to give 14.4V
First test with 12V 50Ah = 0.6kWh lead-acid
Test successful if it works 24h or more (25 W max load, or 2A at 12V).
First test failed because router consumption is rather big, Will measure it after new converter arrival...

Target system power backup time is 1 week = 170h


Count consumption:
3.5W HDD
6.0W CAM (DC meter shows 4.2W average consumption of 2 cameras, up to 6W on some wireless scan)
60W ROU

DigitalMy

2022-01-24 10:11

administrator   ~0007138

Last edited: 2022-01-24 17:40

View 3 revisions

Output in charge controller is the same as battery voltage,
but consumer needs +12.0V exactly stable constant voltage.
Need stabilizer DC to accept range from +10V to +19V as input and +12V output

Found LTC3780 boards on market
Best is DC/DC adapter:
MEAN WELL DDR-120A-12 device for rail
Mean Well SD-100A-12

DigitalMy

2022-01-26 15:42

administrator   ~0007139

Input side:
charger has 3-wire connector to mains
N - neutral, null = zero
L - load, live = 230V AC wave
FG = functional ground (free) terminal

DigitalMy

2022-01-27 23:56

administrator   ~0007141

Last edited: 2022-01-28 00:11

View 2 revisions

Tested XH-M601 battery charging control board 12V
it is based on NE555P chip and relay
it is made to control (switch on or off) external charger or whatever we need, in depend of voltage
2-inputs are parallel, for battery and volt-meter connection
issue is that sense of BAT with charger



DigitalMy

2022-01-29 00:41

administrator   ~0007142

Got factory made UPS for 12V battery Jpower rated 3.0A
It has AC 230V input and 2pcs DC outputs directly from battery through relay (discharge protection).
Changed output from default 13.5V to 13.0V and connected load - it works fine

Jpower_3A.JPG (148,544 bytes)
Jpower_3A.JPG (148,544 bytes)

DigitalMy

2022-02-02 22:33

administrator   ~0007148

Last edited: 2022-02-02 22:45

View 2 revisions

Tested module YX-X850
based on relay 5V DC.
It cannot switch uninterruptedly without rework:
output must have diode, and capacitor after that (before load)
keep in mind voltage drop 0.5V with it - add to power source.
Or use load which accepts interruption...
YX850 is a power failure automatic switch
similar to HW-712 XH-M350



switch_XY-X8V2_YX-X850.jpg (159,907 bytes)
switch_XY-X8V2_YX-X850.jpg (159,907 bytes)