View Issue Details

IDProjectCategoryView StatusLast Update
0007461vehicle serviceToyota SERApublic2024-09-02 02:13
ReporterDigitalMy 
PrioritynormalSeverityminorReproducibilityhave not tried
Status resolvedResolutionfixed 
Summary0007461: Repair windshield wiper control relay EXY10
DescriptionWiper motor under hood left side
 has integrated "idle position" switch for connection power on motor, return wipers to idle
TagsNo tags attached.

Activities

DigitalMy

2024-08-28 22:09

administrator   ~0014347

In OFF and ACC modes: L (blue) line is GND (by maybe relay)

DigitalMy

2024-08-28 22:15

administrator   ~0014348

7.4. Motor 85070-18010 wiper connector 4-pin+1pin:
M01: (blue-black)
M02: (blue-orange)
M03: (blue) = +12V switched by ignition ON, fused 20A
M04: (blue-yellow)
M00: GND (black with red dots) - separately framed
Now in zero position GND connected to M01 and M03

DigitalMy

2024-08-28 22:20

administrator   ~0014349

Switch common wiper with washer, has 6-pin connector.
4 pins:
P01. LO (blue-orange) "+2" = high speed power to motor
P02. LB (blue-black) "+1" = slow speed power to motor
P03. LY (blue-yellow) "+S" = input from wiper motor internal switch (+12V or -12V)
P04. BL (blue) "+B" = power input fused +12V , same as go to washer motor and wiper motor
2-pins:
P05. WL "W" = washer motor (white-blue)
P06. WB "EW" = frame GND (white-black)

DigitalMy

2024-08-29 02:01

administrator   ~0014351

Last edited: 2024-08-30 12:25

View 4 revisions

84652-18010 disassembled
board has one 5-pin relay Taiko CX-10N (LG CX-ION) = "R1"
C1. one capacitor 16V 220mF
D1. diode (power to transistor)
ZD1. Zener diode , in parallel to transistor output, stabilize voltage level for relay coil.
Tr1. C3112 B - transistor making intervals

E = (-)V, frame permanent GND



EXY10_switch_wiper_inside.jpg (561,600 bytes)

DigitalMy

2024-08-29 03:48

administrator   ~0014352

Last edited: 2024-08-29 04:46

View 2 revisions

Relay has in default state "idle" OFF, LO, HI switch positions: NC (+S terminal) connected to +S1 by "COM".
Normally open contact on B+ 12V -> supplied to "COM" +S1 first terminal on multiposition switch OFF or INT
relay controlled by (-) pin
relay (-) pin controlled by transistor Tr1 with ZD1 , cause +B is permanent on relay coil.
Transistor has permanent (-), but (+) comes only in case INT1 joined INT2 if "INT" multiposition switch state,



EXY10_switch_wiper_board_scheme.jpg (447,758 bytes)

DigitalMy

2024-08-29 17:48

administrator   ~0014353

Last edited: 2024-09-02 02:11

View 2 revisions

found damaged by rust magnet in motor
/85070-18010 /85070-18020
/85070-18011 /85070-18021

done glue magnet back to enclosure with epoxy putty,
made abrasive polish and cleaning,
applied "CV" grease to rotor ball-end

After this repair wiper works fine in all 3 modes: INTerval, LOW, HIGH