View Issue Details
ID | Project | Category | View Status | Date Submitted | Last Update |
---|---|---|---|---|---|
0000095 | vehicle service | Toyota SERA | public | 2014-04-30 12:09 | 2021-04-11 16:09 |
Reporter | DigitalMy | ||||
Priority | normal | Severity | minor | Reproducibility | N/A |
Status | progress | Resolution | open | ||
Summary | 0000095: Replace (fix) EXY10 car suspension broken after winter | ||||
Description | 1. draglinks (steering) *2 /45503-19155 or /45503-19185 ->delay (no problem found by me in 2014) -> replaced 2018-01 -> done 2. steering tips (END SUB-ASSY, STEERING RACK, FRONT) *2 /45046-19205 ->delay, one replaced (R) -> replaced 2018-01 -> done 3. bearings front axle 2 *2 /90369-35029 -> replaced right one in 2017, now no problem with sound from it -> done 4. 0000066 -> done 5. drive shafts *2 -> to fix 5.1. / 43410-10150 (rh) (+ 43410-10160 (rh) 5.2. / 43420-10150 (lh) , including: SHAFT ASSY, FRONT DRIVE OUTBOARD JOINT /43420-10160 (lh) (+ or 43470-19475) 6. shaft boots (seal, BOOT KIT, FRONT DRIVE SHAFT) *2 / 04438-12171 ->replaced 2016 -> done 7. transaxle filter (together with gearbox), STRAINER ASSY, VALVE BODY OIL filter /35330-12020 -> delay, replaced with "new" unit 0000080 -> done 8. PAN SUB-ASSY, AUTOMATIC TRANSAXLE OIL /35106-12070 ->delay, replaced with "new" unit + gasket /35168-12020 -> done 9. Front shock absorbers -> done 9.1. top support seat and insulator 10. rear shock absorber /48530-18030 (48530-18010) *2 -> 600x160x150 -> (Kayaba 341082 or Tokico U2940) , chosen Tokico U2940 -> done + spring coil /48231-10240 *2 -> OBK C4T16052 -> done 11. FRONT STABILIZER *2 + CUSHION, FRONT STABILIZER /48817-10020 (also Febest 0123EXZ10F or SWAG 81 94 2982) -> done 12. Front brake support (fix with grease) -> 0000133 -> fixed with seal kit (Frenkit 251012) -> done 13. silentblock replacement for ARM SUB-ASSY, FRONT SUSPENSION, LOWER *2 / Febest (TAB-051 + TAB-052)*2 -> to do 2018 14. engine mounting insulators 15. REAR suspension BUSH 16. Rear axle bearing | ||||
Tags | No tags attached. | ||||
|
16. Rear axle: ordered NK 764514 bearing as replacement for 90366-17010 (external bearing) + 90366-27001 (internal bearing) + 90311-38037 (seal) + 90252-04001 (split pin) -> installed after 1 ride got backlash again, adjusted tension with wrench -> done 2016 |
|
5. Front axle try: run gear when front wheel up (use jack) -> done -> got crack sounds in shaft(s): CV(s) or bearing(s), left side more than right, inner end more that outer, also both hub bearings to be replaced. replace both sides (bearing and seal) FOR FRONT AXLE HUB: bearing D=35\68mm H=33mm /90369-35029 -> replace H12016JC (BTA)* or Koyo DAC3568W-6CS81 + RING, HOLE SNAP /90521-75003 + SEALs /04422-10040 -> Musashi T1284 Currently: hub nut is M22x1.5mm, wrench 30mm + both sides, front L+R make shaft check and switch to used shaft(s) rebuilt on RIGHT and LEFT side + compatible ABS axle HUB(s) have to prepare 1 set (hub+shaft+nut) compatible with "ABS", Installed "Right" hub with ABS and old CV shaft there without ABS, -> need to prepare "ABS" shaft and replace it: put on COVER, FRONT DRIVE SHAFT DUST, RH -> also hub bearing is not very silent on "R" side do need to prepare "L" ABS set: replace BOOTs (KIT, FRONT DRIVE SHAFT) buy "L" axle hub use special CV remover to separate |
|
1. STEERING RACK /44250-18010 ordered and received used assy -> but test above does not show this rack mulfunction -> delay replacement 2. Replaced END SUB-ASSY, TIE ROD, RH on right side after 1 year (was damaged indeed) with original used. /45046-19205 replacement had not fixed main rattling (from hub bearing), original nut M12 |
|
9. Shock absorber FRONT 9.2. ABSORBER ASSY, SHOCK, FRONT /48510-18010 rh -> Tokico B2186 (with fatter rod) -> replaced (was B2188 with thinner rod) /48520-18010 lh -> Tokico B2187 (with fatter rod) -> replaced (was B2189 with thinner rod) 9.3. BUMPER, FRONT SPRING, NO.1 - protect from dust, rubber /48331-16060 *2 -> Febest TSHB20 -> installed 9.4. SPRING, FRONT COIL /48131-16660 *2 -> Masuma CS1014 -> replaced (was the same) 9.5. Seal in the absorber upper plates /90303-22049 (ordered Febest TSD001) -> to replace 2018 Also have old absorbers KYB 333067 (R) + 333068 (L) Monroe |
|
10. Shock absorber REAR suspension 10.1. ABSORBER ASSY rear /48530-10090 or 48530-10260 (original /48530-10080) *2 -> TOKICO U2940 -> bought (EMEX) ->replaced 10.2. Coil spring rear /48231-10240 can be replaced with OBK C4T16052 -> delay (it was OBK already, C4T16052H ?) 10.3. boots BUMPER, REAR SPRING *2 /48341-10090 -> ordered original (exist), installed 2014 10.4. RETAINER(FOR REAR SUPPORT TO REAR SHOCK ABSORBER) *2 /90948-02082 -> ordered original (exist), installed 2014 |
|
9.1. Replace later top of front stand (both): 9.1.1. SUPPORT SUB-ASSY, FRONT SUSPENSION *2 /48609-18010 - plate with 4pcs screw 9.1.2. 48680D SEAL, DUST(FOR FRONT SUSPENSION SUPPORT) /90303-22049 -> 9.5 9.1.3. SEAT SUB-ASSY, FRONT SPRING, NO.1 *2 /48044-10030 - plate under support 9.1.4. INSULATOR, FRONT COIL SPRING, UPPER *2 /48157-10020 - inside plate Support part was /48681-18010 ? (above support) |
|
15. REAR suspension: execute extended test and conclude... BUSH, REAR SUSPENSION ARM, NO.3 *2 /48725-10031 -> replace /48725-10040 or /48725-16150 L=60mm D=55mm d=12.5mm l=44mm compatible MTP MTA108 , Febest TAB-071 -> later BUSH, LATERAL CONTROL ROD *2 /90385-18015 -> later |
|
13. FRONT suspension arms: Replace both ARMs with silentblocks: left /48069-16060 /48069-10070 (purchased CTR CQT-17L) right /48068-16060 /48068-10090 (purchased CTR CQT-17R) on left side cracked main BOLT (FOR FRONT SUSPENSION LOWER ARM) /90119-12099 |
|
|
|
|
|
|
|
|
|
|
|
11. Stabilizer bar (front) connector to arm: prepare two sets of assy: need 4pcs rubber cushion and 2pcs M8 W12 nuts on each side (L,R) CUSHION, FRONT STABILIZER /48817-10020 (purchased SAT ST4881710020, similar cheaper SAT ST4881730020) prepared, replaced 2018-08-31 (white) -> done 11.1 BUSH, FRONT STABILIZER BAR, NO.1 /48815-10090 2pcs replaced compatible "Febest TSBRZJ120R" 2018-08-31 cracked /91611-60822 bolt for front stabilizer bush bracket, 4pcs, W=12mm one broken in body M6*20? -> drilled out, replaced 2018 from other car -> done |
|
|
|
14. Engine support (12371A INSULATOR, ENGINE MOUNTING, REAR) bottom center /12371-11280 /12371-11340 /12371-11360 "silent block" -> do inspection first |
|
|
|
|
|
|
|
2020: wheel nut damaged left on bolt right front, drill out with 12mm (cobalt-coated) and install new bolt -> done right arm bent (impact) -> replace arm -> done 0002345 |